Scion xb 1st gen sevice repair book pdf download

You may also like documents download: Toyota tundra ewd electrical wiring diagram. After your payment via PayPal or credit card, you will have instant access to your download. Dont need to wait for shipping. Download link for the manual will appear on the checkout page after your payment is completed. Additionally a few seconds after your payment you will receive an email with your instant manual download link. You have three days after payment to download and save your manual.

Only logged in customers who have purchased this product may leave a review. Click to enlarge. Add to Wishlist. Product added! Browse Wishlist. You are reading a preview. Create your free account to continue reading. Sign Up. Like this document? Why not share! Embed Size px. Start on. Show related SlideShares at end. WordPress Shortcode.

Next SlideShares. Download Now Download to read offline and view in fullscreen. Download Now Download Download to read offline. Related Books Free with a 30 day trial from Scribd. Related Audiobooks Free with a 30 day trial from Scribd. Elizabeth Howell. Justo Danilo Winter Pop. Views Total views. Actions Shares. No notes for slide. Check that the battery cables are connected to the correct terminals. Disconnect the battery cables when the battery is given a quick charge.

Do not perform tests with a high voltage insulation resistance tester. Never disconnect the battery while the engine is running. Check that the charging cable nut is tightened on terminal B of the generator and the engine room relay block. Check the electrolyte level. If the electrolyte level is low, replace the battery or add distilled water and check the charging system. Check the color of the indicator. If it has not been 20 minutes since you drove the vehicle or since the engine was stopped, turn the ignition switch to the ON position and turn on the electrical systems headlight, blower motor, rear defogger, etc.

This will remove the surface charge from the battery. Turn off the ignition switch and the electrical systems. Standard voltage: If the voltage is below the specification, charge the battery. Check that the battery terminals are not loose or corroded. If the terminals are corroded, clean them. Standard resistance: Below 1 ohms If the result is not as specified, replace the fuses as necessary. Check the belt for wear, cracks or other signs of damage. If any of the following defects is found, replace the V-ribbed belt.

Check that the belt fits properly in the ribbed grooves. HINT: Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley. If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly. Check that the generator wiring is in good condition.

If the condition is not good, repair or replace the generator wire. Check that there is no abnormal noise from the generator while the engine is running. If there is abnormal noise, replace the pulley or generator. Turn the ignition switch to the ON position. Check that the charge warning light comes on. Start the engine and check that the light goes off. If the light does not operate as specified, troubleshoot the charge warning light circuit.

According to the following procedure, connect an ammeter and voltmeter as shown in the illustration. Disconnect the wire from terminal B of the generator and connect it to the negative - lead of the ammeter.

Ground the negative - lead of the voltmeter. Check the charging circuit. Standard current: 10 A or less Standard voltage: If the results are not as specified, replace the generator assembly. HINT: If the battery is not fully charged, the ammeter reading may be more than the standard current.

Keep the engine speed at 2, rpm, turn on the high beam headlights, and turn the heater blower switch to the "HI" position. This manual PDF download provides detailed service information, step-by-step procedures for disassembly and reassembly, inspection, maintenance, component identification and unit repair, along with service specifications for the Toyota Scion xB - NCP31 Series model vehicle. This manual PDF download is designed primarily for use by trained mechanics in a properly equipped shop.

However, it contains enough detail and basic information to make it useful to the owner who desires to perform his own basic maintenance and repair work. A basic knowledge of mechanics, the proper use of tools, and workshop procedures must be understood in order to carry out maintenance and repair satisfactorily.